Single-Wall vs. Type B Furnace Vent Pipe: Why We Upgraded This Garage Furnace
We replaced a single-wall furnace vent with double-wall Type B in an Orange County garage. Here's why clearance and safe venting matter.

We recently replaced a furnace vent pipe on a Lennox gas furnace in a garage here in Orange County. The old pipe was single-wall metal. We installed double-wall Type B vent in its place.
A furnace vent that is the wrong type, too close to wood, or starting to rust is easy to miss and important to fix.

What we found in this garage
The furnace sits in a garage, with ducts above it and the vent rising from the top of the cabinet. The original connector was single-wall metal: one layer of pipe, with no insulating air space. The outside gets hot, and it needs plenty of room between the metal and anything that can burn.
We removed that pipe and installed listed double-wall Type B vent. Type B has an inner and outer pipe, with air in between. That extra wall allows a much smaller clearance to nearby wood, and it helps the exhaust stay hotter as it travels up and out. We also installed a condensate pump at the furnace, which moves drain water when it cannot flow by gravity.
This kind of upgrade often happens during a heating visit or a furnace repair, when a technician can see the pipe and the clearances — not just whether the furnace turns on.
Single-wall pipe vs. Type B
Two points matter most for a homeowner.
Clearance to wood and other combustibles. For a typical listed gas furnace approved for Type B vent, a single-wall metal pipe generally needs 6 inches of clearance to combustible material. Type B is installed at the clearance in its listing, which manufacturers commonly specify as 1 inch. The California Mechanical Code clearance table uses 6 inches for single-wall pipe on those listed appliances, and “as listed” for Type B. A City of California City mechanical checklist states the same idea: single-wall vent 6 inches, double-wall Type B 1 inch minimum. In a tight space, 6 inches is often hard to keep.
Where single-wall pipe is not allowed. California Mechanical Code section 802.7.3.2, which follows NFPA 54, says single-wall metal pipe shall not originate in an unoccupied attic or concealed space, and shall not pass through an attic, inside wall, concealed space, or floor. Placer County’s official inspection checklist quotes that section verbatim. A short single-wall connector in the same open room as the furnace can still be allowed if those rules and the clearances are met. We look at where the pipe runs and how close it sits to wood, then upgrade to Type B when the layout or the clearance calls for it.
Why this matters
The vent is how a gas furnace sends combustion gases, including carbon monoxide, out of the house. The U.S. Consumer Product Safety Commission recommends a yearly professional inspection of the heating system, including chimneys and flues for blockages, corrosion, and loose or disconnected joints. CPSC notes that blocked, leaking, or damaged flues can release carbon monoxide into the home. Their carbon monoxide fact sheet is a good homeowner reference, and every home with a gas furnace should have working CO alarms.
The type of pipe also affects draft and corrosion. A Dura-Vent handbook written to align with NFPA 54 explains that Type B’s air-insulated double wall keeps flue gases hotter, supports a stronger draft, and reduces condensation. Single-wall galvanized connectors lose more heat. When exhaust cools too much, acidic moisture can condense inside the pipe and rust the metal over time.
Signs your furnace vent should be checked
You do not need to diagnose the pipe yourself, but these are worth a closer look before winter:
Rust, flaking metal, holes, or a white powdery residue on the vent pipe
A single-wall pipe that runs tight to wood, or that goes through a wall, floor, ceiling, or attic
Loose, separated, or poorly supported joints
Water stains, dripping, or a musty smell around the furnace
Soot, scorch marks, or discoloration on or near the pipe
A furnace that starts, then shuts off, or a faint exhaust smell when it runs
A carbon monoxide alarm that sounds — if that happens, get everyone outside and call 911
Some of those signs can also point to other heating problems, so a licensed technician should inspect the system.
When to call
Call if you see any of the signs above, if a home inspector flagged the vent, or if your furnace is in a garage and you are not sure what kind of pipe you have. The best time is a heating maintenance visit before winter, when we can check the vent with the rest of the system. If the furnace is at the end of its life, venting is also part of a proper furnace installation.
GoTech Air Conditioning & Heating is based in Laguna Niguel and serves Orange County. We are licensed and insured, CSLB #1120123 (C-20). Hours are Monday–Sunday, 7:00 AM–7:00 PM. Emergency service is available during those hours. Same-day service is available when the schedule allows.
Call (949) 228-6242, contact us, or book online. You can also start on our heating services page.